Broken tie rod?

Mike_Yates

Literotica's Anti-Hero
Joined
Jan 5, 2006
Posts
15,449
Many years ago when I was a little kid the tie rod broke on my mother's van and the wheel literally fell off.

That van was a piece of shit that was constantly in the shop being repaired.

Have you ever snapped a tie rod?
 
Tie rods don't keep wheels attached, they just keep them pointed in the right direction.

Never broken one, but I've bent them. I used my winch to straighten it enough to get to where I could replace it.
 
Yes. It's always inconvnient, as I seem to be steering at the time. It gives you terrible mileage on your affected tire.

The repairs seem to be way more costly than they used to be, as the steering suspension rigs are more complex. You can't just have them welded and re-enforced with angle iron.

On the other hand, warranties are way longer than they used to be, and are more likely to cover such mishaps.
 
A little bit of maintenance goes a long way to prevent this sort of thing:rolleyes:

I just got my brakes done yesterday because I couldn't stand the grinding anymore.
 
A little bit of maintenance goes a long way to prevent this sort of thing:rolleyes:

I just got my brakes done yesterday because I couldn't stand the grinding anymore.

Yeah, if your pads are gone the caliper starts grinding and ruins your rotor.
 
nowadays its cheaper to put on new rotors than to turn them anyway.

$600.00 for all 4 rotors and pads, installed

That's a costly job.

It's important to get the pads replaced as soon as they go or they can ruin the brake rotor.
 
Replaced the pads with plywood once, not for long though couldn't stand the burning smell
 
Many years ago when I was a little kid the tie rod broke on my mother's van and the wheel literally fell off.

That van was a piece of shit that was constantly in the shop being repaired.

Have you ever snapped a tie rod?

Yes, sort of.

At 50 miles an hour, on a curve, over railroad tracks.

It ruined the summer for both myself and the other driver, we both came out of it with broken limbs and totalled vehicles.

Eventually it was discovered that the mechanic who loaned me the vehicle, while he worked on my car, didn't put the bolts on right.
 
No.

I have had a wheel fall off.

A previous owner had persistently overtightened the wheel nuts and they cut through the wheel.

I had to replace all five wheels. At the time they cost me a whole £1.00 each.

My father broke a half-shaft on his car in the centre of Westminster Bridge during the rush hour. He caused a snarl-up in most of West London.
 
No.

I have had a wheel fall off.

A previous owner had persistently overtightened the wheel nuts and they cut through the wheel.

I had to replace all five wheels. At the time they cost me a whole £1.00 each.

My father broke a half-shaft on his car in the centre of Westminster Bridge during the rush hour. He caused a snarl-up in most of West London.

So if you break a tie rod, the wheel doesn't fall off?
 
Tie rods do NOT keep the wheel on. I call bullshit. Think I lack the knowledge to know the diference? Trust the 'wrench, he has spent way too many years in the pits at dirt tracks pulling wrenches.

Yes, I have had a tie rod break while driving- many years ago, about 60 miles per hour on a gravel road. Very interesting trying to keep it between the ditches while trying to stop.

Also, due to a mismeasurement by a crewchief- many broken tie rods on a race car one summer. We figured out the problem, fixed it, and went on to put the car back in the winner's circle where it belonged.

BUT NEVER DID A WHEEL FALL OFF DUE TO A BROKEN TIE ROD.
 
That's because the tie rod isn't connected to the wheel...
 
Alright, then what do you have to break in order to risk the wheel falling off?

Well both ball joints would have to suddenly turn to powered.

The spindle would have to break along with the brake lines.

Now a rear wheel...once...there was a pop in the deferential and the left rear axle just eased on out of the housing, wheel, tire and all.
 
Alright, then what do you have to break in order to risk the wheel falling off?
Aside from broken wheel studs/missing lug nuts it depends entirely on the design of the axle/suspension. There are a number of different designs.
 
Had a wheel bearings go many times, only thing holding the wheel in place was the calliper wishbone broke and ball joints gone at different times, wheels were all over the place bet never actually came off even had a driveshaft pop out on a fiat x19 lost drive but wheel never fell off. Once forgot to tighten nuts, that was the closest

Incidentally, the plywood brake pads stayed in place due to pins and springs, it was a desperate get home measure. They did catch fire after a few miles
 
Back
Top